customized gift for birthday
customized gift for birthday
pillow cases linen
linen sheets
pillow cases linen Embroidering Dandelions Plus Free Embroidery Design decorative pillow shams
Views: 67 Updated: :2020-03-09

This project uses a design included in the new BERNINA Exclusive Embroidery Collection Handcrafted Monograms #80294. Specialty fabrics, BERNINA Embroidery Software 8.1 and features on the BERNINA embroidery machine make this project easy and fun to complete.

Step 1 Mark the horizontal and vertical center of each 11″; square of Kraft-Tex using a chalk marker.

pillow covers vintage

Step 2 Hoop StabilStick TearAway Stabilizer paper side up and score paper inside of hoop. Tear paper away to expose sticky side of stabilizer.

Step 3 Position one Kraft-Tex square in center of hoop using marks and/or hoop template.

Step 4 In software, retrieve pattern 80294-75. Remove bottom flying dandelion pieces and words. Save as a different file name than original, i.e. 80294-75a.

Step 5 While second file is still retrieved on the screenpillow cases linen, remove top flying dandelion pieces. This will leave just the flower itself. Save as a different file name, i.e. 80294-75b.

Step 6 On machine, retrieve original file (80294-75) and stitch on the first square hooped square, changing colors as suggested. Remove from hoop. Trim stabilizer to size of Kraft-Tex square.

Step 7 Repeat Steps 2 and 3 to hoop a second 11” square. Stitch the second design created in Step 4 (80294-75a). Do NOT remove from the hoop.

Step 8 While second design is still in hoop and attached to machine, retrieve last design created in step 5 (80294-75b). Using the Pinpoint Placement option on the machine, touch below the stem on flower (to the right, if the design has been rotated to fit the hoop).

Use the Multifunction knobs (Stitch Width and Stitch Length knobs) to move the hoop until the needle is over the same stitch on the design in the hoop. Touch the Set icon. Close the Pinpoint Placement tool.

Note –; When a design is opened, it automatically centers in the hoop. This design should stitch to the left side of the square in the same place it stitched in the first two designs.

Step 9 Once the design is lined up in the correct position, remove the hoop from the machine and remove design from hoop. Trim stabilizer to size of Kraft-Tex square.

Hoop another piece of StabilStick following Steps 2 and 3 to center last Kraft-Tex square in the hoop. Stitch last design that was positioned in Step 8. Remove from hoop and trim stabilizer to size of Kraft-Tex square.

Step 10 Cut the faux leather in half to create two pieces 18″; x 45″;. Put one piece aside; it is the backing for the wall-hanging.

Trim the other piece to 36” x 13”. Then cut out the inner 10” squares as shown in the diagram. Cutting the squares from the inside areas creates frames for the Kraft-Tex blocks.

Step 11 Tape design blocks to backside of frame created in step 12 using tearaway tape. See picture of completed projects for order.

Layer backing, batting and top together. Use a 505 spray to hold layers together if desired. Using a decorative sewing stitch, topstitch around the blocks. Work from the center square out. Trim away the excess batting and backing.

Edge stitch around outside edge of wall-hanging to finish. Hang and enjoy, or use it as as an inspirational table runner!

The basement updates are almost complete! Now that we have a beautiful living room area, completed the bathroom & guest suite, it was time to transition the awkward piece of furniture into something more beautiful & more useful! We had always dreamed of a finished lower level where we could relax & entertain guests. We transformed what was once a questionable addition into a diy wet bar.

I had two pairs of jeans that I didn't need. One pair had a rip in the butt-area, and even if I fixed that, it would look awkward.My other pair was a bit baggy because they were hand-me-downs.So I made the best of it and combined them, and this is what turned out.:DThroughout the project, SAVE ALL OF YOUR SCRAPS!

?



Powered by customized gift for birthday @2018 RSS Sitemap html Sitemap

Copyright 站群系统 © 2013-2019 Personalize